Product ID:CORDOBOND STRONGBACK RESIN
MSDS Date:01/01/1985
FSC:8040
NIIN:00N001609
MSDS Number: BCHWS

FERRO CORPORATION, COMPOSITES DIVISION

Emergency Phone: 203-853-2123

Cage: 0LG38

FERRO CORPORATION

SANTA BARBARA, CA 93117-3092 US

Telephone: 805-968-5000

Cage: 0LG38

ALLYL GLYCIDYL ETHER (AGE)

CAS: 106-92-3

RTECS: RR0875000

Fraction By Weight: 5%

OSHA PEL (C) 10 PPM

ACGIH TLV: S,5 PPM/10 STEL;9293

EPICHLOROHYDRIN/BISPHENOL A MIXTURE

Fraction By Weight: 95%

Effects of Overexposure:SKIN, RESPIRATORY & EYE IRRITATION & INJURY.
SLIGHT IRRITATION TO NASAL PASSAGE.

First Aid:REMOVE FROM EXPOSURE, FLUSH SKIN & EYES WITH PLENTY OF H*20
FOR 15 MIN. CALL MD FOR EYES. REMOVE CONTAMINATED CLOTHING
IMMEDIATELY & DISCARD

Flash Point:285F,140C, COC
Extinguishing Media:CO*2, DRY CHEM, FOAM
Fire Fighting Procedures:WEAR SELF-CONT BRTH APPAR.
Unusual Fire/Explosion Hazard:HEAT INCREASES VAP PRESS OF TOXIC AGE &
DECOMP EMITS CO & H*20. IGNITION HAZ IS MODERATE.

Spill Release Procedures:SCRAPE UP EXCESS RESIN & RETURN SPILLED
MATERIAL TO WASTE CONTAINER. SCRUB AWAY SPILLAGE WITH SOAPY H*20 OR
DETERGENT. PROTECT SKIN FROM CONTACT. WEAR HEAVY WORK GLOVES OR
BUTYL RUBBER GLOVES.

Handling and Storage Precautions:STORE < 125F, 51C. AVOID OPEN FLAMES.
DO NOT SMOKE. WIPE UP SPILLS IMMEDIATELY. CONFINE MIXING,LAY-UP &
CURING OPERATIONS TO VENTED AREAS OR OUTDOORS.
Other Precautions:DISCARD CONTAMINATED CLOTHING IMMEDIATELY. MAINTAIN
CLEAN EQUIP & WORK AREAS. WHEN ADDING HARDENER TO RESIN,EXOTHERMIC
REACTION OCCURS WITHIN 15-20 MIN, REACHING TEMPS 400F,204C.

Respiratory Protection:NIOSH/MSHA APPRVD CANNISTER MASK WHEN MIXING
HARDENER & RESIN (MFR)
Ventilation:MECH VENT RECOMND TO KEEP BELOW TLV.
Protective Gloves:BUTYL RUBBER
Eye Protection:FACE SHIELD
Other Protective Equipment:HEAVY WORK CLOTHES OR COVERALLS
Supplemental Safety and Health
PART A OF TWO PART KIT. BP & VAP DENSITY ARE FOR AGE. VAP PRESSURE FOR
AGE- 1.7 AT 60F; 15C, 4.5 AT 90F; 32C. PRODUCT HAS STORAGE LIFE OF
< 24 MOS AT 125F; 51C.

Boiling Pt:B.P. Text:309F,153C
Vapor Pres:1.7
Vapor Density:3.4
Spec Gravity:1.25
Solubility in Water:SLIGHT
Appearance and Odor:MILKY, SLIGHTLY VISCOUS LIQ, MILD ODOR
Percent Volatiles by Volume:<5

Stability Indicator/Materials to Avoid:YES
AMMONIA OR AMINES, STRONG OXIDIZING AGENTS
Stability Condition to Avoid:PREMATURE ADDITION OF AMINES OR HEATING TO
DECOMPOSITION
Hazardous Decomposition Products:CO, CO*2
Conditions to Avoid Polymerization:PREMATURE ADDING OF AMINE HARDENER
W/AMMONIA OR AMINES.

Waste Disposal Methods:DISPOSAL METHODS MUST BE IAW FEDERAL, STATE &
LOCAL REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.